Section 1
PRODUCT IDENTIFICATION
| PRODUCT NAME OR NUMBER | Riptide |
| PRODUCT DESCRIPTION | Heavy duty Chlorinated Warewashing Concentrate |
| CHEMICAL FAMILY | N/A |
| D.O.T. PROPER SHIPPING NAME | Corrosive Solid, N.O.S. (contains sodium Hydroxide) |
| SHIPPING ID NUMBER | UN1759 |
| HAZARD CLASS | 8 (Corrosive Material) Package Group II |
| HMIS RATING | Health-3, Flammability-0, Reactivity-1, See section 8 for protective clothing. |
Section 2
HAZARDOUS INGREDIENTS / HAZARD DATA
| CHEMICAL NAME(S) | CAS NUMBER | TLV-TUA | PEL |
| Sodium Hydroxide | 1310-73-2 | 2 mg/m3 | 2 mg/m3 |
| Sodium Dichloro-S-Triazinetrione | 2893-78-8 | 0.5 ppm TWA | 0.5 ppm TWA |
| Sodium Carbonate | 497-19-8 | N/E | N/E |
| Sodium Metasilicate | 6834-92-0 | N/E | N/E |
| This product contains no other ingredient considered hazardous according to the criteria of 29 CFR 1910.1200, OSHA | |||
Section 3
PHYSICAL DATA
| BOILING/MELTING POINT @760 nm Hg | N/A |
| pH | 2500 ppm Solution - 12.3 |
| VAPOR PRESSURE mm Hg @ 20½ C | N/A |
| VAPOR DENSITY (Air = 1) | N/A |
| PERCENT VOLATILE BY WEIGHT (%) | N/A |
| SPECIFIC GRAVITY OR BULK DENSITY | N/A |
| SOLUBILITY IN WATER | Complete |
| EVAPORATION RATE (BuAc = 1) | N/A |
| APPEARANCE | White Granular Powder |
| ODOR | None added |
Section 4
FIRE AND EXPLOSION HAZARD DATA
| FLASH POINT ½F (Test Method) | N/A |
| AUTOIGNITION TEMPERATURE | N/A |
| FLAMMABILITY LIMITS IN AIR (% V) | N/A |
| EXTINGUISHING MEDIA | This product does not support flames, but can react violently with water. |
| SPECIAL FIRE FIGHTING PROCEDURES | Use NiOSH certified gas mask with canister for chlorine. If possible, remove cotainer to open air and flood with water. |
| UNUSUAL FIRE & EXPLOSION HAZARDS | Product may react with some metals such as aluminum, zinc, tin, etc., to release flammable hydrogen gas. This product can react violently with water. |
Section 5
HEALTH HAZARD DATA
EFFECTS OF OVEREXPOSURE
| SKIN CONTACT | Corrosive. Contact may cause severe irritation, dermatitis, and chemical burns. |
| EYE CONTACT | Corrosive. Causes eye burns. May cause temorary or permanent vision loss and blindness. |
| INHALATION | Corrosive. Inhalation of dust or mist may cause irritation to nose, throat, and mucous membranes, pulmonary irritation, pulmonary edema, tissue damage and chemical burns. |
| INGESTION | Corrosive. Harmful or fatal if swallowed. May cause nausea, vomiting, and severe tissue damage to digestive tract. Corrosive to mouth, throat, stomach and to other tissues. |
| CHRONIC EFFECTS OF OVEREXPOSURE | None |
| TOXICOLOGICAL TEST DATA | Caustic Soda, the key ingriedient in this product is a corrosive material. Acute Dermal LD50 (rabbit) 1350 mg/kg |
Section 6
EMERGENCY AND FIRST AID PROCEDURES
| SKIN | Immediately wash with plenty of water for at least 15 minutes. Remove contaminated clothing and footwear. Wash clothing before reuse and discard footwear which cannot be decontaminated. Seek medical attention immediately. |
| EYES | Immediately flush eyes with large amounts of water for at least 15 minutes forcibly holding lids apart to ensure flushing of entire surface, then seek medical attention immediately. |
| INGESTION | Never give anything by mouth to an unconscious person. If swallowed, do not induce vomiting. Give large quantities of water.Then seek medical attention immediately. |
| INHALATION | Remove to fresh air. If breathing is difficult have trained person administer oxygen. If respiration stops, give mouth to mouth resuscitation. Get medical attention. |
Section 7
REACTIVITY DATA
| PRODUCT STABILITY | stable |
| Stability Conditions to Avoid | Mixing with any other cleaning product. Mix only with below 150 degrees water. Avoid temperature above 100 degrees, and high humidity to prevent caking. |
| CHEMICAL INCOMPATIBILITY | Phosphoric acid, Muratic Acid, and other acidic materials, reducing agents, hydrocarbons, alcohols, ether, ammonia, ammoniated compounds and aluminum. |
| HAZARDOUS DECOMPOSITION PRODUCTS | Mixing with incompatible materials may produce hydrazine, chloring, hydrogen, and other toxic and irritating fumes. |
| HAZARDOUS POLYMERIZATION | None |
| Polymerization Conditions to Avoid | N/A |
Section 8
SPECIAL PROTECTION INFORMATION
| RESPIRATORY PROTECTION | Dust mask for handling greater than 25 Ibs. |
| VENTILATION | Satisfactory adequate ventilation.Local exhaust is not ordinarily needed. Avoid inhalation of dust containing this product. |
| PROTECTIVE CLOTHING | Wear full-cover protective clothing to prevent repeated or prolonged contact. |
| EYE PROTECTION | Safety glasses, safety goggles, and an eye-wash station. |
| OTHER PRECAUTIONS | N/A |
Section 9
ENVIRONMENTAL DATA
| SPILL OR LEAK PROCEDURES | Use proper protective equipment. Carefully sweep up and shovel into dry containers without raising dust. Cover containers and move containers out of spill area. |
| WASTE DISPOSAL METHOD | Comply with all federal, state, and local regulations. Consult state and local authorities for restrictions on disposal of chemical waste. |
| CONTAINER DISPOSAL | Please recycle empty containers whenever possible. |